2008 Honda Accord Maintenance Schedule

2008 Honda Accord maintenance at a glance

The 2008 Honda Accord belongs to the 8th generation (2008-2012), built with 2.4L K24 four-cylinder or 3.5L J35 V6 with cylinder deactivation. It takes 5W-20 synthetic blend. Oil changes run 5,000 - 10,000 miles on the Maintenance Minder. This is the first model year of that generation, so it is the build most likely to carry early-production quirks and the most likely to have accumulated technical service bulletins.

What a 2008 model needs now

A 2008 Honda Accord is 18 years old in 2026, which at an average 12,000 miles a year puts it around 216,000 miles - long-term ownership. Beyond 216,000 miles maintenance is mostly about deciding what is worth doing. Rubber and plastic components fail on age rather than mileage, corrosion matters as much as wear, and knowing what has already been replaced is the difference between a sound investment and throwing money at an unknown. On that mileage estimate it should already have had timing components on chain-driven engines and a full fluid refresh at 180,000 miles.

Key intervals for the 8th generation

Known issues on the 2008 Accord

The fault most worth knowing about on this generation is Variable Cylinder Management on the V6 causing oil consumption and spark plug fouling. Owners also report Excessive oil consumption on the 2.4L K24, traced to piston ring design on some builds; and Premature front brake pad and rotor wear, a common complaint across this generation. None of these are certainties on any individual vehicle - they are the patterns worth checking for when you buy or when a symptom appears.

Track your 2008 Honda Accord service history free with the ServiceSage maintenance tracker, or compare it against other model years on the Honda Accord maintenance schedule hub.

2008 Honda Accord maintenance schedule

IntervalService
Maintenance Minder Code AEngine oil change (5W-20 full synthetic), Reset the oil life monitor
Maintenance Minder Code BReplace engine oil and filter, Rotate tires, Inspect brakes and brake fluid, Inspect suspension and steering, Inspect driveshaft boots, exhaust, and fuel lines
Sub-code 1Rotate tires
Sub-code 2 (typically every 30,000 mi)Replace engine air filter, Replace dust and pollen (cabin) filter, Inspect drive belt
Sub-code 3 (typically every 30,000-60,000 mi)Replace transmission fluid (ATF DW-1) - drain and fill, never a high-pressure flush
Sub-code 4 (typically every 100,000 mi)Replace spark plugs, Inspect valve clearance, Inspect the water pump, and on the 3.5L V6 replace the timing belt
Sub-code 5Replace engine coolant (Honda Long Life Type 2, blue)
Sub-code 7Replace brake fluid (DOT 3)

What is due at each mileage - 2008 Honda Accord

The table above is indexed by service interval. This is the same schedule indexed by odometer reading, for when you know your mileage and want the list. If your odometer sits between these figures, work back to the last one you passed and catch up anything skipped.

OdometerService due
30,000 mi (48,000 km)Replace engine air filter, Replace dust and pollen (cabin) filter, Inspect drive belt.
60,000 mi (97,000 km)Same as the 30,000 mi service.
100,000 mi (161,000 km)Replace spark plugs, Inspect valve clearance, Inspect the water pump, and on the 3.5L V6 replace the timing belt.
120,000 mi (193,000 km)Same as the 30,000 mi service.
150,000 mi (241,000 km)Same as the 30,000 mi service.
200,000 mi (322,000 km)Same as the 100,000 mi service.

Honda schedules this vehicle by Maintenance Minder code rather than by odometer, so the mileages above are the typical points those codes appear - the car itself decides, based on how it has been driven.

2008 Honda Accord oil life reset

Maintenance Minder reset (SEL/RESET knob)

  1. Ignition to ON/II, engine off.
  2. Press the SEL/RESET knob repeatedly to cycle the display until "Engine Oil Life %" or the Maintenance Minder code appears.
  3. Press and hold SEL/RESET for about 10 seconds, until the oil-life percentage and maintenance code(s) start blinking.
  4. To reset only the completed item, rotate the knob to highlight it first. To reset everything, press and hold SEL/RESET again for about 5 more seconds while it is blinking.
  5. The display stops blinking and resets to 100% - reset confirmed.