John Deere 4044M Maintenance Schedule

John Deere 4044M maintenance — the short answer

  • Oil: John Deere Plus-50 II preferred; John Deere Torq-Gard Supreme also preferred. Other oils must meet API CJ-4 or CK-4, ACEA E6 or E9, or JASO DH-2. Viscosity: SAE 15W-40, 10W-40, 10W-30, 0W-40, or 5W-30. · 5.4 L (5.7 qt) with filter (5.3 L / 5.6 qt in the 2018 and 2020 manuals)
  • Oil change interval: every 200 hours or 12 months (400 hours from serial KL100001, model year 2020, per Deere's current manual)
  • Engine: Yanmar 4TNV88C 4-cylinder diesel (4TNV88C-MJT2V in the current manual), 31.7 kW (42.5 hp) gross at 2,600 rpm, Final Tier 4 with exhaust filter (DOC + DPF)
  • Tracked by: engine hours, not miles

John Deere 4044M maintenance schedule by engine hours

IntervalServiceDetails
Every 10 hoursDaily / 10-Hour ChecksEvery 10 hours or daily (inspection only): test the safety systems; check the engine oil level; check and drain the water separator; check the transmission/hydraulic oil level; check the coolant level; check and clean the front grille screen; check and clean the air filter rubber dust valve. The daily start-up procedure also covers wheel bolts, tire pressure, debris and leaks.
Every 50 hoursLubrication (Grease Fittings and 3-Point Hitch)Every 50 hours: lubricate the machine - the 3-point hitch lift-link grease fitting, the ball joints and drawbar (with SUPER LUBE), and the front axle trunnion fittings (multi-purpose grease). In wet conditions grease every 10 hours or daily (a condition-based figure, not the normal interval). Grease: John Deere Multi-Purpose SD Polyurea or HD Lithium Complex preferred, otherwise NLGI No. 2.
Every 50 hoursFront Axle Oil Level CheckEvery 50 hours (inspection only): check the front axle oil on the dipstick after letting it settle for 1 hour.
Every 50 hoursCab Filters Clean or Replace (cab models)Every 50 hours on cab tractors: clean the cab air filters with compressed air and replace them if damaged.
Every 50 hoursCab and ROPS Mounting Torque CheckAfter the first 10 hours, check the cab/ROPS mounting hardware torque; then check the cab mounting bolt torque every 50 hours (260 N-m / 192 lb-ft).
Every 50 hoursFront Hitch Hardware Torque Check (if equipped)Every 50 hours on tractors with a front hitch: check the front hitch hardware torque.
Every 100 hoursFront Hitch Hydraulic Leak Check (if equipped)Every 100 hours on tractors with a front hitch: check the front hitch hydraulic connections for leaks.
Every 200 hours or 12 months, whichever comes firstAir Restriction Indicator CheckEvery 200 hours or yearly: check the air restriction indicator light. A check only - the air filter itself is serviced every 600 hours, or replaced when the indicator calls for it.
Every 200 hours or 12 months, whichever comes firstAlternator/Fan Belt CheckEvery 200 hours or yearly: inspect and, if needed, adjust the alternator/fan belt - 9 mm (3/8 in) of deflection at 334 N (75 lb). On cab tractors also check and adjust the A/C compressor belt. Replace a belt only when it is worn, damaged or stretched.
Every 200 hours or 12 months, whichever comes firstWheel Bolt Torque CheckEvery 200 hours or yearly. On a new tractor, or whenever wheel hardware has been loosened, tighten all bolts after 1 hour of operation and every 4 hours after that until the torque holds; the 2018 and 2020 manuals also list a check after the first 10 hours. Torque: 140 N-m (103 lb-ft) front and rear.
Every 200 hours or 12 months, whichever comes firstEngine Oil & FilterEvery 200 hours or 12 months, whichever comes first, is the schedule for tractors built before serial KL100001 (model years 2014-2019), and Deere's 4M-series filter overview sheets (February 2019, and May 2021 with an open-ended serial range) still print it for oil filter M806419. From serial KL100001 (model year 2020) on, John Deere's operator's manuals (OMTR112287, and the current OMTR130411 for serial PR000001-) set it at 400 hours or 12 months, so on a 2020-or-later tractor 400 hours is the manufacturer's interval. We list 200 hours because a reminder cannot tell the two serial ranges apart, and an early oil change costs only the oil. Oil: John Deere Plus-50 II or Torq-Gard Supreme preferred; otherwise API CK-4 or CJ-4, ACEA E6 or E9, or JASO DH-2, viscosity by air temperature (SAE 15W-40, 10W-40, 10W-30, 0W-40 or 5W-30). Capacity with filter: 5.4 L (5.7 qt) in the current manual, 5.3 L (5.6 qt) in the 2018 and 2020 editions. Extreme heat, dust, or constant low-speed or short-run work need more frequent changes (no figure given).
Every 400 hours or 12 months, whichever comes firstPrimary Fuel Filter / Water SeparatorEvery 400 hours or yearly, whichever comes first: replace the primary fuel filter / water separator (MIU802421 per Deere's filter overview) and drain water from the fuel tank. Checking and draining the water separator is a separate daily check.
Every 400 hours or 12 months, whichever comes firstFinal Fuel FilterEvery 400 hours or yearly, whichever comes first: replace the final fuel filter (MIU803127 per Deere's filter overview). The fuel system bleeds itself: turn the key to ON for 10-15 seconds before starting.
Every 400 hoursTransmission & Hydraulic Oil ChangeEvery 400 hours, together with the transmission filter and the hydraulic suction filter. The transmission, rear axle and hydraulics share one oil, so this is the only hydraulic or transmission fluid change - not two. Deere allows the oil change (not the filters) to stretch to 1,200 hours or 3 years only if all three hold: John Deere Hy-Gard or Low Viscosity Hy-Gard is used, both filters are still changed every 400 hours, and a transmission oil sample (Oil Scan) is taken every 400 hours or once a year. Deere's filter overview sheets print the 1,200-hour figure without those conditions; the operator's manual chart says 400. Oil: John Deere Hy-Gard (J20D) factory fill, Low Viscosity Hy-Gard below -18 C (0 F); others must meet JDM J20C or J20D - never engine oil or Type F ATF. Capacity 47.3 L (12.5 gal). Check the level daily.
Every 400 hoursTransmission Oil FilterEvery 400 hours, even when the oil itself is on the extended 1,200-hour plan. Part number per Deere's filter overview: RE45864 (the May 2021 sheet also lists LVA23443). The filter can be changed without draining the oil by holding a shop vacuum on the filler opening.
Every 400 hoursHydraulic Suction Oil FilterEvery 400 hours, also on the extended oil plan (Deere's filter overview: LVA10419, replace after every 400 hours). This is a filter replacement, not a fluid change - the fluid is the shared transmission/hydraulic oil.
Every 400 hoursFront PTO Gearbox Oil & Filter (if equipped)Every 400 hours on tractors with a front PTO: replace the front PTO gearbox oil (JD20D, as the manual writes it) and its filter. It is on the current manual's 400-hour service record and in the 2018 and 2020 charts; the current chart table leaves it out.
Every 600 hoursAir Filter Service and Inspection (replace as required)Every 600 hours, service the air filter elements, intake hoses and clamps: inspect them and replace the elements as required - this is not a fixed 600-hour replacement. Replace the primary element (RE68048) when it is restricted or damaged. The secondary (safety) element (RE68049) does not need routine replacement; inspect it in place, and if you do replace it, fit a new primary at the same time. Inspect the intake hoses each time the filter is changed, and at least yearly.
Every 600 hoursFront Axle (MFWD) Oil ChangeEvery 600 hours: drain the differential plug and both axle drain plugs, then refill through the dipstick opening. Oil: John Deere Hy-Gard or Low Viscosity Hy-Gard (JDM J20C/J20D). Capacity, standard axle: 5.5 L (5.8 qt) in the current manual, 5.0 L (5.3 qt) in the 2018 and 2020 editions (the 8.0 L heavy-duty axle is on the 4052M/4066M HD only). The current manual's 600-hour service record says 'check' where its chart and every earlier edition say 'change'; we follow the chart.
Every 600 hoursFront Axle Thrust Bolt Torque CheckEvery 600 hours: check the front axle thrust bolt torque (standard axle 30 N-m / 22 lb-ft, jam nut 70 N-m).
Every 600 hoursBrake Adjustment CheckEvery 600 hours: check the brake adjustment.
Every 600 hoursEngine Idle Speed CheckEvery 600 hours: check the engine high idle (2,750 rpm) and low idle (950 rpm) speeds. New in the current manual's chart; not in the 2018 or 2020 editions.
Every 1,000 hoursEngine Valve Clearance Check (dealer)Every 1,000 hours: have a John Deere dealer check and adjust the engine valve clearance.
Every 6,000 hours or 6 years, whichever comes firstCoolant Drain, Flush & RefillEvery 6,000 hours or 6 years, whichever comes first, when the system holds John Deere COOL-GARD II or COOL-GARD II PG (the coolant Deere lists) and the coolant is tested every year. With any other coolant, or without the yearly test, Deere's coolant page says every 2,000 hours or 2 years, but its maintenance chart prints that case as 2,000 hours or annually - go by the shorter, yearly figure. Deere says to see your dealer for this service. Capacity: open station 6 L (6.3 qt), cab 7.6 L (8 qt).
Every 12 monthsCoolant Test (Test Strips)At least every 12 months, and whenever coolant is lost to leaks or overheating: test the coolant with John Deere COOL-GARD II test strips, and add COOL-GARD II Coolant Extender only if the strip chart calls for it. This yearly test is what qualifies the 6,000-hour / 6-year drain interval. Check the coolant level daily.
Every 12 monthsHoses and Clamps CheckEvery year (inspection): check all hoses and clamps, including the air intake hoses and connections.

John Deere 4044M specifications

  • Type: Compact Tractor
  • Engine: Yanmar 4TNV88C 4-cylinder diesel (4TNV88C-MJT2V in the current manual), 31.7 kW (42.5 hp) gross at 2,600 rpm, Final Tier 4 with exhaust filter (DOC + DPF)
  • Displacement: 2.2 L (133.6 cu in)
  • Oil type: John Deere Plus-50 II preferred; John Deere Torq-Gard Supreme also preferred. Other oils must meet API CJ-4 or CK-4, ACEA E6 or E9, or JASO DH-2. Viscosity: SAE 15W-40, 10W-40, 10W-30, 0W-40, or 5W-30.
  • Oil capacity: 5.4 L (5.7 qt) with filter (5.3 L / 5.6 qt in the 2018 and 2020 manuals)

John Deere 4044M items without a fixed hour interval

  • First 10-Hour Checks (one-time): One time, after the first 10 hours: check the windshield wiper arm mounting hardware torque (cab), the safety interlock system and the ROPS mounting hardware torque. The 2018 and 2020 manuals also put the first wheel bolt torque check here.
  • Battery Inspection / Cleaning (as required): No hour or calendar interval: the current manual lists battery cleaning and replacement under Service - As Required. Check the electrolyte level and add distilled water only; clean the terminals with a baking-soda solution (four tablespoons per gallon of water). The 2014-2017 manuals did list cleaning and checking the battery every 50 hours.
  • Exhaust Filter (DPF) Ash Service (dealer): No fixed interval. The engine controller warns when the exhaust filter needs ash cleaning or replacement, which does not happen before 3,000 hours. Dealer service only - never clean the DPF with water or chemicals. DPF part number for the 4044M per Deere's filter overview: MIU803276. Run parked or auto regeneration when the indicator asks for it.
  • Serial Number Differences (KL100001 break): Engine oil and filter: 400 hours or 12 months from serial KL100001 (model year 2020) on, per OMTR112287 and OMTR130411; 200 hours or annually before that (OMLVU32571 and earlier) and on Deere's 4M filter overview sheets. This schedule lists 200 hours so that one reminder is safe on every tractor. The 2014-2017 editions (OMLVU28780, OMLVU29832, OMLVU32267) also list cleaning and checking the battery and checking tire pressure every 50 hours, and servicing the fuel injection nozzles every 2 years or 2,000 hours; the July 2014 edition also drains the coolant every year or 1,000 hours if it is not tested annually.

Frequently asked questions

How often should I change the oil in a John Deere 4044M?

Change the oil in the John Deere 4044M every 200 hours of run time or every 12 months, whichever comes first (400 hours from serial KL100001, model year 2020, per Deere's current manual). The 200-hour figure is the one for tractors built before serial KL100001 and the one on Deere's 4M-series filter sheets, so check your serial before stretching it. The crankcase holds 5.4 L (5.7 qt) with the filter; Deere prefers John Deere Plus-50 II. Because it is measured in engine hours, log the hour-meter reading rather than a date.

What is the maintenance schedule for a John Deere 4044M?

The John Deere 4044M is serviced on engine hours, not miles. Key intervals include Engine Oil & Filter (every 200 hours or 12 months; 400 hours from serial KL100001, model year 2020, per Deere's current manual), Transmission & Hydraulic Oil Change (every 400 hours), Front Axle (MFWD) Oil Change (every 600 hours). Track the hour meter and service each item when its interval comes due.

Does the John Deere 4044M track maintenance by hours or miles?

By hours. Small engines and heavy equipment log run time on an hour meter, so their service intervals are hours-based. ServiceSage Auto tracks the John Deere 4044M by hours and reminds you when each service is due.