John Deere 3038E Maintenance Schedule

John Deere 3038E maintenance — the short answer

  • Oil: John Deere Plus-50 II (preferred) or Torq-Gard Supreme; other oils meeting API CJ-4 or CK-4, ACEA E6 or E9, or JASO DH-2, viscosity by air temperature · 4.3 L (4.5 qt) with filter
  • Oil change interval: every 200 hours or 12 months (400 hours on serial KL100001 up to NP000001, per Deere's 2020 manual)
  • Engine: Yanmar 3TNV86CT-NJT2V 3-cylinder liquid-cooled diesel (S/N KL100001-; 3TNV86CT-NJT2 on HJ100000-KL100000), 27.4 kW (36.7 hp) gross per SAE J1995, glow-plug start, exhaust filter (DOC + DPF)
  • Tracked by: engine hours, not miles

John Deere 3038E maintenance schedule by engine hours

IntervalServiceDetails
Every 10 hoursEngine Oil Level CheckEvery 10 hours or daily (inspection only): check the engine oil level.
Every 10 hoursTransmission Oil Level CheckEvery 10 hours or daily (inspection only): check the transmission/hydraulic oil on the dipstick after the tractor has cooled for at least 1 hour.
Every 10 hoursCoolant Level CheckEvery 10 hours or daily (inspection only): check the coolant level against the FULL HOT / FULL COLD marks on the recovery tank.
Every 10 hoursAir Cleaner Dust Valve CheckEvery 10 hours: squeeze the rubber dust unloading valve on the air cleaner canister to clean it, and replace it if damaged.
Every 10 hoursSafety Interlock System TestEvery 10 hours or daily, before use: test the safety interlock system.
Every 50 hoursGrease Points LubricationEvery 50 hours in normal conditions, every 10 hours in wet conditions: grease the lubrication points, including the front axle trunnion fittings. The operator's manual names no grease type ('recommended grease or equivalent').
Every 50 hours3-Point Hitch LubricationEvery 50 hours, if equipped: grease the lift link fitting and lubricate the ball joints and drawbar hitch with SUPER LUBE.
Every 50 hoursFront Axle Oil Level CheckEvery 50 hours (inspection only): check the front axle oil level on the dipstick after letting the oil settle for 1 hour.
Every 200 hoursAlternator Belt InspectionEvery 200 hours: inspect the alternator/fan belt and check the tension - about 9 mm (3/8 in) of deflection under 334 N (75 lb). Replace it only if worn, damaged or stretched.
Every 200 hoursWheel Bolt Torque CheckEvery 200 hours (the yearly service record lists it too). On a new tractor, check after the first 10 hours of use; whenever wheel hardware has been loosened, tighten all bolts after 1 hour of operation and every 4 hours after that until the torque holds.
Every 200 hours or 12 months, whichever comes firstEngine Oil & Filter ChangeEvery 200 hours or 12 months, whichever comes first, is the schedule for 3038E tractors before serial KL100001 (serials HJ100000-KL100000 per manual OMLVU33981, and earlier), and it is what Deere's 3E-series filter overview sheet (February 2019, still on deere.com) prints for oil filter M806419. Deere's operator's manual for serial KL100001 up to the NP000001 break (OMTR112397) sets it at 400 hours or 12 months, so on those tractors 400 hours is the manufacturer's interval; the manuals for later serials (OMTR135276, OMTR153655) are not public and were not checked. We list 200 hours because a reminder cannot tell the serial ranges apart, and an early oil change costs only the oil. Oil: John Deere Plus-50 II (preferred) or Torq-Gard Supreme; otherwise API CJ-4 or CK-4, ACEA E6 or E9, or JASO DH-2, viscosity by air temperature. Capacity with filter: 4.3 L (4.5 qt). Filter: M806419. Extreme heat, dust, constant low engine speed or frequent short runs call for more frequent service (no figure given).
Every 400 hours or 12 months, whichever comes firstFuel Filters & Water Separator ReplaceEvery 400 hours or yearly, whichever comes first: drain water from the fuel tank and replace the fuel filters - on the 3032E/3038E the procedure covers the sediment-bowl filter (fuel/water separator element), the in-line pre-fuel filter and the fuel filter. Part numbers from Deere's 2019 filter overview: fuel/water separator MIU802421 and final fuel filter MIU803127 on S/N 610001 and later (M811032 and MIU800645 before that); Deere's Worldwide parts guide for serial NP100000 and later lists M811032, MIU800645 and MIU803127, so check the part numbers for your serial. The system bleeds itself: key ON for 10-15 seconds before starting. Draining the separator is a separate daily check.
Every 400 hoursTransmission & Hydraulic Oil ChangeEvery 400 hours, together with both filters. The transmission and hydraulics share one reservoir, so this is the only hydraulic or transmission fluid change. Oil: John Deere Low Viscosity Hy-Gard (J20D), or oil meeting JDM J20C/J20D - never engine oil or Type F ATF. Capacity 20.8 L (5.5 gal). Deere allows the oil change to stretch to 1,200 hours or 3 years only with Hy-Gard or Low Viscosity Hy-Gard, both filters still changed every 400 hours, and an oil sample taken every 400 hours or once a year. Severe or unusual conditions need more frequent service. No calendar limit is given. Serial NP000001 and later were not checked (their manuals are not public), and Deere's Worldwide parts guide for serial NP100000 and later lists this oil at 1,200 hours or 3 years - check the manual for your serial before going past 400 hours.
Every 400 hoursTransmission (HST) & Hydraulic Suction Filters ReplaceEvery 400 hours, at each transmission/hydraulic oil change - and still every 400 hours if the oil change is extended to 1,200 hours. Filters: HST/transmission LVA16054 and hydraulic suction LVA14703 (Deere's 2019 filter overview). Older tractors (2016 manual, S/N 710001 on) and Deere's 2019 filter sheet call for a first transmission oil and filter change at 50 hours; the KL100001 manual lists no 50-hour item.
Every 600 hoursAir Filter Service (Replace Primary Element)Every 600 hours: service the air filter element and intake hoses - remove and discard the primary element (M131802) and fit a new one. The secondary (safety) element (M131803) does not need routine replacement: inspect it in place, never clean it, and if you replace it, fit a new primary too. Replace elements sooner as required. Inspect the air intake hoses and connections whenever the filter is changed, and at least yearly.
Every 600 hoursFront Axle (MFWD) Oil ChangeEvery 600 hours: drain the differential and both front axle drain plugs, then refill through the dipstick opening. Oil: John Deere Hy-Gard or Low Viscosity Hy-Gard (JDM J20C/J20D). Capacity 3.8 L (4 qt). The manual's 600-hour service record says 'check' where its chart says 'change'; we follow the chart.
Every 600 hoursFront Axle Thrust Bolt Torque CheckEvery 600 hours: check the front axle thrust bolt torque (14 N-m / 10 lb-ft).
Every 600 hoursEngine Idle Speed CheckEvery 600 hours: check the engine low idle (950 rpm) and high idle (2,650 rpm) speeds. Listed on the manual's 600-hour service record, not in its interval chart.
Every 600 hoursBrake Adjustment CheckEvery 600 hours: check the brake adjustment; see your John Deere dealer if the brakes are not working properly. Listed on the manual's 600-hour service record, not in its interval chart.
Every 1,000 hoursEngine Valve Clearance Check (dealer)Every 1,000 hours: have a John Deere dealer check the engine valve clearance.
Every 6,000 hours or 6 years, whichever comes firstCooling System Drain, Flush & RefillEvery 6,000 hours or 6 years, whichever comes first, with John Deere Cool-Gard II or Cool-Gard II PG pre-mix that is tested every year. With any other coolant, or without the yearly test, Deere's coolant page says every 2,000 hours or 2 years, but its maintenance chart prints that case as 2,000 hours or annually - go by the shorter, yearly figure. Deere marks this a dealer service. 3038E cooling system capacity 5.2 L (5.5 qt); keep the coolant concentration at 40-60%.
Every 12 monthsCoolant Condition TestAt least every 12 months, and whenever coolant is lost to leaks or overheating: test the coolant with John Deere Cool-Gard II test strips. The 6,000-hour / 6-year drain interval depends on this yearly test.
Every 12 monthsHoses & Clamps InspectionEvery year (inspection): check all hoses and clamps; replace radiator hoses and clamps as required.

John Deere 3038E specifications

  • Type: Compact Tractor
  • Engine: Yanmar 3TNV86CT-NJT2V 3-cylinder liquid-cooled diesel (S/N KL100001-; 3TNV86CT-NJT2 on HJ100000-KL100000), 27.4 kW (36.7 hp) gross per SAE J1995, glow-plug start, exhaust filter (DOC + DPF)
  • Displacement: 1.6 L (95.7 cu in), 3 cylinders, 86 x 90 mm
  • Oil type: John Deere Plus-50 II (preferred) or Torq-Gard Supreme; other oils meeting API CJ-4 or CK-4, ACEA E6 or E9, or JASO DH-2, viscosity by air temperature
  • Oil capacity: 4.3 L (4.5 qt) with filter

John Deere 3038E items without a fixed hour interval

  • Fuel Water Separator Check & Drain: Daily: check the fuel sediment bowl / water separator and drain any water. If water and deposits are found, remove the bowl and replace the fuel filter. The chart lists this as daily, with no hour figure.
  • Front Grille Screen Check: Daily: check and clean the front grille and side screens. The chart lists this as daily, with no hour figure.
  • Daily Pre-Start Checks: Before each day's work (the manual's daily start-up procedure): check tire pressure, the air filter elements and dust valve, and the fuel level; clean the air intake and radiator screens; remove grass and debris from the machine; check under the machine for leaks; and check the wheel bolt torque. Inspection only.
  • Serial Number Differences (KL100001 and NP000001 breaks): Engine oil and filter: 400 hours or 12 months on serial KL100001 up to the NP000001 break (OMTR112397); 200 hours or yearly before KL100001 (OMLVU33981 and earlier). This schedule lists 200 hours so that one reminder is safe on every tractor. Older tractors (2016 manual OMLVU31846, serial 710001 on) also call for a first transmission oil and filter change, with the suction screen cleaned, after the first 50 hours, and list smaller capacities: engine oil 4.0 L, coolant 4.8 L, fuel tank 23.5 L, transmission and hydraulic 21 L. Serial NP000001 and later (manuals OMTR135276 and OMTR153655) were not checked: those manuals are not public, and Deere's Worldwide parts guide for serial NP100000 and later lists the transmission/hydraulic oil at 1,200 hours or 3 years and different fuel filter part numbers - use your own manual.
  • First 10-Hour Check (new tractor): One time on a new tractor: check the wheel bolt torque after the first 10 hours of use. After that it is checked every 200 hours. Any time wheel hardware has been loosened, tighten all bolts after 1 hour of operation and every 4 hours after that until the torque holds.

Frequently asked questions

How often should I change the oil in a John Deere 3038E?

Change the oil in the John Deere 3038E every 200 hours of run time or every 12 months, whichever comes first (400 hours on serial KL100001 up to NP000001, per Deere's 2020 manual). The 200-hour figure is the one for tractors built before serial KL100001 and the one on Deere's 3E-series filter sheet, so check your serial before stretching it. The crankcase holds 4.3 L (4.5 qt) with the filter; Deere prefers John Deere Plus-50 II. Because it is measured in engine hours, log the hour-meter reading rather than a date.

What is the maintenance schedule for a John Deere 3038E?

The John Deere 3038E is serviced on engine hours, not miles. Key intervals include Engine Oil & Filter Change (every 200 hours or 12 months; 400 hours on serial KL100001 up to NP000001, per Deere's 2020 manual), Fuel Filters & Water Separator Replace (every 400 hours or 12 months), Transmission & Hydraulic Oil Change (every 400 hours). Track the hour meter and service each item when its interval comes due.

Does the John Deere 3038E track maintenance by hours or miles?

By hours. Small engines and heavy equipment log run time on an hour meter, so their service intervals are hours-based. ServiceSage Auto tracks the John Deere 3038E by hours and reminds you when each service is due.