John Deere 318G Maintenance Schedule

John Deere 318G maintenance — the short answer

  • Oil: John Deere Plus-50 II SAE 15W-40, API CK-4/SN (TY26673). See the operator's manual for viscosity by operating temperature · 7.5 L (2.0 gal)
  • Oil change interval: every 250 hours
  • Engine: Turbocharged 4-cylinder diesel, EPA Final Tier 4 (Yanmar 4TNV86CHT)
  • Tracked by: engine hours, not miles

John Deere 318G maintenance schedule by engine hours

IntervalServiceDetails
Every 10 hoursLubrication PointsEvery 10 hours or daily: lubricate boom linkage, cylinder, and Quik-Tatch pivot points
Every 10 hoursFluid Level ChecksEvery 10 hours or daily: check engine oil level, coolant level, and hydraulic system oil level. These are level checks only - the engine oil change itself is the 500-hour service
Every 50 hoursQuik-Tatch Engagement PinsEvery 50 hours: lubricate Quik-Tatch engagement pins, and check and clean the dust unloader valve (M89679)
Every 250 hoursEngine Oil SampleEvery 250 hours: take an engine oil sample for fluid analysis. This is a sampling step, not an oil change
Every 500 hoursEngine Oil & FilterDrain and refill engine oil and replace filter every 500 hours. Oil: John Deere Plus-50 II SAE 15W-40 (TY26673) | Capacity: 7.5 L (2.0 gal) | Filter: MIU800650
Every 500 hoursFuel FilterEvery 500 hours: replace the primary fuel filter and water separator (MIU801025) and the final fuel filter (MIU801090), and drain water and sediment from the fuel tank
Every 500 hoursChain Case Oil LevelEvery 500 hours: check chain case oil level. John Deere Hy-Gard (TY6354), 14.3 L (3.8 gal) per side - the machine has a chain case on each side
Every 500 hoursChassis LubricationEvery 500 hours: lubricate foot pedals (if equipped) and steering linkage (if equipped)
Every 500 hoursFluid SamplingEvery 500 hours: take hydraulic oil, engine coolant, and diesel fuel samples for analysis. Based on results, intervals may need adjusting for operating conditions
Every 1,000 hoursHydraulic Fluid & FilterDrain and refill hydraulic oil and replace filter every 1000 hours. John Deere Hydrau hydraulic and hydrostatic system oil, 22.7 L (6.0 gal) | Filter: AT314164
Every 1,000 hoursChain Case Oil ChangeEvery 1000 hours: drain and refill chain case oil. John Deere Hy-Gard (TY6354), 14.3 L (3.8 gal) per side
Every 1,000 hoursBreather ReplacementEvery 1000 hours: replace the hydraulic oil reservoir breather (AT443309) and the fuel tank breather (H216169)
Every 1,000 hoursCoolant Condition CheckEvery 1000 hours: check coolant condition. Full drain, flush and refill is the 6000-hour service
Every 1,500 hoursValve ClearanceEvery 1500 hours: check and adjust engine valve lash. Rocker arm cover gasket MIU800399
Every 6,000 hoursCoolant FlushEvery 6000 hours: drain, flush, and refill the cooling system. John Deere Cool-Gard II Pre-Mix (TY26575), 12.0 L (3.2 gal)

John Deere 318G specifications

  • Type: Skid Steer Loader
  • Engine: Turbocharged 4-cylinder diesel, EPA Final Tier 4 (Yanmar 4TNV86CHT)
  • Displacement: 2.1 L (127.6 in)
  • Oil type: John Deere Plus-50 II SAE 15W-40, API CK-4/SN (TY26673). See the operator's manual for viscosity by operating temperature
  • Oil capacity: 7.5 L (2.0 gal)

John Deere 318G items without a fixed hour interval

  • Air Filter: As required: replace primary (AT338105) and secondary (AT336803) engine air filter elements, and check and clean the cooling package
  • Cab Air Filter: As required (if equipped): replace cab fresh air filter element (AT441536) and cab recirculation air filter element (AT359416)
  • Tire Inspection: As required: check tire pressure and wheel lug nut torque. The 318G is a wheeled skid steer on 10x16.5 tires - it has no tracks
  • Drive Belt Inspection: As required: check accessory drive belt, and lubricate the steering centering mechanism (if equipped)

Frequently asked questions

How often should I change the oil in a John Deere 318G?

Change the oil in the John Deere 318G every 250 hours of run time. Because it is measured in engine hours, log the hour-meter reading rather than a date.

What is the maintenance schedule for a John Deere 318G?

The John Deere 318G is serviced on engine hours, not miles. Key intervals include Lubrication Points (every 10 hours), Fluid Level Checks (every 10 hours), Quik-Tatch Engagement Pins (every 50 hours). Track the hour meter and service each item when its interval comes due.

Does the John Deere 318G track maintenance by hours or miles?

By hours. Small engines and heavy equipment log run time on an hour meter, so their service intervals are hours-based. ServiceSage Auto tracks the John Deere 318G by hours and reminds you when each service is due.