Kubota SVL75-2 Maintenance Schedule

Kubota SVL75-2 maintenance — the short answer

  • Oil: API CJ-4 (DPF-compatible) diesel engine oil: SAE 30, 10W-30 or 15W-40 above 25 C; SAE 20, 10W-30 or 15W-40 at 0-25 C; SAE 10W or 10W-30 below 0 C · 10 L (10.6 US qt) with filter
  • Oil change interval: every 250 hours (Australian-edition interval; the US manual may say 500 hours)
  • Engine: Kubota V3307-CR-TE4 turbocharged 4-cylinder diesel, 55.4 kW gross / 51.3 kW net, EPA Tier 4 with DPF and EGR
  • Tracked by: engine hours, not miles

Kubota SVL75-2 maintenance schedule by engine hours

IntervalServiceDetails
Every 10 hoursGrease All FittingsEvery 10 hours (daily). Grease the fittings on both sides of the machine: lift arm linkage (1), link 1 (1), bucket link pin (1), control link (2), lift arm cylinder boss (2), tilt cylinder boss (2) and quick-hitch pin (1). For loader work in water, grease generously before work and again afterward. Grease examples from the manual: Shell Alvania EP2, Mobilux EP2.
Every 10 hoursEngine Oil Level CheckEvery 10 hours (daily check, inspection only). Check on level ground, 5 minutes after stopping the engine. If the level is above the upper limit, the oil has been diluted by fuel from DPF regeneration and must be changed right away.
Every 10 hoursHydraulic Oil Level CheckEvery 10 hours (daily check, inspection only). Read the sight gauge on the hydraulic tank at normal temperature (10-30 C); the level should be near the center of the gauge. Do not mix different oils.
Every 10 hoursCoolant Level CheckEvery 10 hours (daily check, inspection only). With the engine cooled down, the coolant should be between the FULL and LOW marks on the recovery tank.
Every 10 hoursWater Separator DrainEvery 10 hours (daily), and right away if the red float reaches the line or error code E:9120 appears. Drain the water, then purge air from the fuel system. This only drains water - the separator element itself is replaced every 500 hours.
Every 10 hoursFuel Level CheckEvery 10 hours (daily check, inspection only). Use ultra-low-sulfur diesel: No.2-D above -5 C, No.1-D below -5 C. Tank capacity 93 L.
Every 10 hoursRadiator and Oil Cooler CheckEvery 10 hours (daily check). Look for clogged fins and ribs and clean them with compressed air (under 205 kPa) or steam.
Every 10 hoursV-Belt CheckEvery 10 hours (daily check, inspection only): look for cracks and check the tension. The tension is adjusted every 250 hours.
Every 10 hoursEvacuator Valve CheckEvery 10 hours (daily): open the air cleaner evacuator valve to get rid of large particles of dust and dirt.
Every 10 hoursEngine and Electrical Wiring CheckEvery 10 hours (daily check): remove flammable debris from the battery, wiring, muffler and engine, and look for loose or shorted terminals.
Every 10 hoursDPF Muffler CheckEvery 10 hours (daily check): make sure nothing flammable has collected around the DPF muffler.
Every 10 hoursBattery Condition CheckEvery 10 hours (daily check, inspection only - not a replacement interval). On a refillable battery keep the electrolyte between the UPPER and LOWER marks. Battery: 12 V, RC 160 min, CCA 900 A.
Every 10 hoursFuel and Hydraulic Hose Leak CheckEvery 10 hours (daily check, inspection only): look for oil leaks at the fuel and hydraulic hose connections. The same inspection table adds a monthly and a yearly hose inspection.
Every 10 hoursFuel Tank Cap CleaningEvery 10 hours (daily): clean the fuel tank cap.
Every 10 hoursWasher Liquid Check (closed cab)Every 10 hours (daily check), closed-cab models: keep the window washer tank filled.
Every 50 hoursTrack Tension Check and AdjustEvery 50 hours, beginning 50 hours after the machine is put into service. With the machine on jack stands, the gap between the outer end of the track roller and the inside of the track should be 20-30 mm; adjust if needed. This is a check and adjustment, not a track replacement. The manual also says to clean the track after every use.
Every 50 hoursAir Cleaner Outer Element CleaningEvery 50 hours: take out only the outer element and blow it clean from the inside out with compressed air under 205 kPa. Do not remove the inner element. In extremely dusty conditions inspect and clean it more often (the manual gives no figure). Both elements are replaced every 250 hours or after the sixth cleaning.
Every 50 hoursEvacuator Valve CleaningEvery 50 hours: remove the dust cover and clear debris from behind the evacuator valve.
Every 50 hoursFuel Tank Water DrainEvery 50 hours: open the drain shutoff valve under the cover and drain water from the fuel tank.
Every 250 hoursEngine Oil and Filter ChangeChange the engine oil and replace the oil filter cartridge together; after the first run, top the oil up to make up for what the new filter holds. 250 hours is the interval in Kubota's SVL75-2 operator's manual, English (Australia) edition (V0522-5814-4), the edition Kubota publishes free online. Kubota's US manual for the sister SVL97-2 gives engine oil and filter at 500 hours (and its Canadian manual gives the filter at 500 hours) where its Australian manual says 250, so the US SVL75-2 manual may say 500 hours - check the manual for your serial number before you extend it. Capacity: 10 L (10.6 US qt) with the filter. Oil: API CJ-4 (DPF-compatible); SAE 30, 10W-30 or 15W-40 above 25 C, SAE 20, 10W-30 or 15W-40 at 0-25 C, SAE 10W or 10W-30 below 0 C. Harder-than-usual conditions call for shorter intervals (no figure given).
Every 250 hoursAir Filter Element Replacement (outer and inner)Every 250 hours or after the sixth cleaning of the outer element, whichever comes first: replace both the outer and the inner element, using Kubota genuine elements. Never take the inner element out for cleaning; if it has been removed, fit a new one. Shorten the interval in dusty or sandy conditions (the manual gives no figure).
Every 250 hoursV-Belt Tension AdjustmentEvery 250 hours: the alternator belt should deflect about 4.0-5.0 mm under approx. 50-60 N of thumb pressure; the air-conditioner belt (closed cab) about 7-9 mm. Replace a belt that is worn, cracked or torn.
Every 250 hours or 6 months, whichever comes firstRadiator Hoses and Clamps CheckEvery 250 hours or 6 months, whichever comes first (inspection): tighten loose clamps and replace hoses that are swollen, hardened or cracked. The hoses are replaced every 2 years regardless.
Every 250 hoursFuel Line and Intake Air Line CheckEvery 250 hours (inspection): check that all lines and hose clamps are tight and undamaged, and repair or replace anything worn.
Every 250 hoursMain Frame Interior CleaningEvery 250 hours: clear mud, leaves and debris from inside the main frame.
Every 250 hoursCab Air Filter Cleaning (closed cab)Every 250 hours on closed-cab models: blow out the fresh-air filter and the inner (recirculation) filter against their normal airflow, under 205 kPa. Clean more often in dusty conditions; the filters are replaced every 1,000 hours.
Every 250 hoursAir-Conditioner Condenser Check (closed cab)Every 250 hours on closed-cab models: check that the condenser is clear of debris.
Every 500 hoursFuel Filter Cartridge ReplacementEvery 500 hours, then purge air from the fuel system. Skipping it reduces how well the DPF cleans itself.
Every 500 hoursWater Separator Element ReplacementEvery 500 hours: close the shutoff valve, replace the element, check the O-ring, then purge air from the fuel system.
Every 500 hoursDrive Unit (Travel Gearbox) Oil ChangeFirst change at 250 hours, then every 500 hours. Gear oil: SAE 90 (API GL-4 or GL-5) all year round, about 1.0 L - fill until it runs out of the check port (the manual does not say whether 1.0 L is per drive unit or for both). This is the machine's only drivetrain fluid: the SVL75-2 manual has no transmission or UDT fluid service.
Every 500 hoursHydraulic Oil Filter and Return Filter ReplacementEvery 500 hours: replace the hydraulic oil filter cartridge (raise the cab and lightly oil the new O-ring) and the return filter inside the hydraulic tank. Their first changes come earlier: the oil filter cartridge at 50 hours, the return filter at 250 hours. The return filter is also replaced at each 1,000-hour hydraulic oil change. These are filter changes, not a hydraulic oil change. Hydraulic hammer work shortens the return filter interval (severe duty, not the normal interval): every 300 hours at 20-40% hammer use, every 100 hours at 60% or more.
Every 500 hoursHydraulic Tank Breather ReplacementEvery 500 hours: raise the cab and replace the breather filter above the hydraulic tank.
Every 1,000 hoursHydraulic Oil ChangeEvery 1,000 hours under normal work; the suction filter and the return filter inside the tank are replaced during this change. Capacity: tank 35 L, whole system 60 L. Factory fill is Idemitsu Daphne Super Hydro 46ST; use ISO 32 or ISO 46 hydraulic oil in cold weather or low ambient temperatures and ISO 68 in hot weather or high ambient temperatures (examples in the manual: Shell Tellus S2M 32/46/68, Mobil DTE 10 Excel 32/46). Use only oils from the manual's recommended list - Kubota UDT is not on it - and do not mix different oils. Hydraulic hammer work shortens this (severe duty, not the normal interval): every 800 hours at 20% hammer use, 400 at 40%, 300 at 60%, 200 above that.
Every 1,000 hoursHydraulic Suction Filter ReplacementEvery 1,000 hours, at the hydraulic oil change. Hammer work does not shorten this one.
Every 1,000 hoursEngine Valve Clearance Adjustment (dealer)Every 1,000 hours. A Kubota dealer service.
Every 1,000 hoursCab Air Filter Replacement (closed cab)Every 1,000 hours on closed-cab models, or sooner if the filter is very dirty from dusty work.
Every 1,500 hoursInjector Tip Check (dealer)Every 1,500 hours. A Kubota dealer inspection.
Every 1,500 hoursCrankcase Oil Separator Element ReplacementEvery 1,500 hours: replace the oil separator element and its gasket, and wipe the case clean.
Every 1,500 hoursEGR Cooler Check (dealer)Every 1,500 hours. A Kubota dealer inspection.
Every 2,000 hoursAlternator and Starter Motor CheckEvery 2,000 hours (inspection). Ask your Kubota dealer for details.
Every 3,000 hoursEGR System Check (dealer)Every 3,000 hours. A Kubota dealer inspection.
Every 3,000 hoursTurbocharger Check (dealer)Every 3,000 hours. A Kubota dealer inspection.
Every 3,000 hoursDPF Ash Cleaning (dealer)Every 3,000 hours, by a Kubota dealer with a dedicated cleaning machine. Do not take apart, shake or heat the DPF.
Every 4,000 hours or 2 years, whichever comes firstRadiator Hoses and Clamps ReplacementEvery 2 years or 4,000 hours, and sooner if a hose is swollen, hard or cracked. (The maintenance chart says every 2 years; the manual's important-parts list adds 4,000 hours.)
Every 4,000 hours or 2 years, whichever comes firstFuel Line and Intake Air Line ReplacementEvery 2 years or 4,000 hours: replace the fuel hoses, the intake air line and their clamps.
Every 4,000 hours or 2 years, whichever comes firstHydraulic Hose Replacement (dealer)Every 2 years or 4,000 hours, whether or not wear is visible: a Kubota dealer replaces the hydraulic hoses with new O-rings and seals and Kubota genuine hose. This comes from the manual's list of important parts, not the maintenance chart.
Every 4,000 hours or 2 years, whichever comes firstClosed Breather Rubber Piping Replacement (dealer)Every 2 years or 4,000 hours. A Kubota dealer service.
Every 4,000 hours or 2 years, whichever comes firstDPF Pressure Sensor Rubber Piping Replacement (dealer)Every 2 years or 4,000 hours: the DPF differential pressure sensor rubber piping, front and back. A Kubota dealer service.
Every 4,000 hours or 2 years, whichever comes firstSuction Pipe Downstream of AFS Replacement (dealer)Every 2 years or 4,000 hours: the suction pipe downstream of the air flow sensor. A Kubota dealer service.
Every 4,000 hours or 2 years, whichever comes firstBoost Sensor Rubber Piping Replacement (dealer)Every 2 years or 4,000 hours: the boost sensor pressure rubber piping. A Kubota dealer service.
Every 1 monthFuel and Hydraulic Hose Inspection (monthly)Every month (inspection only): check the fuel and hydraulic hose connections for leaks and the hoses for cracks or chafing.
Every 12 monthsExhaust Manifold Check (dealer)Every year: a Kubota dealer checks the exhaust manifold for cracks, gas leaks and loose mounting screws.
Every 12 monthsIntake Air Line Leak Check (dealer)Every year: a Kubota dealer checks the intake air line for air leaks.
Every 12 monthsBoost Sensor and Air Flow Sensor Check (dealer)Every year: a Kubota dealer checks the boost sensor and the air flow sensor (AFS).
Every 12 monthsDPF Muffler Condition Check (dealer)Every year: a Kubota dealer checks the condition of the DPF muffler. This is separate from the daily owner check for debris around it.
Every 12 monthsDPF Pressure Sensor and Piping Leak Check (dealer)Every year: a Kubota dealer checks the DPF differential pressure sensor and its piping for gas leaks.
Every 12 monthsDPF Temperature Sensor Check (dealer)Every year: a Kubota dealer checks the DPF exhaust gas temperature sensor.
Every 12 monthsEGR Piping Leak Check (dealer)Every year: a Kubota dealer checks the EGR and its piping for gas leaks.
Every 12 monthsFuel and Hydraulic Hose Inspection (yearly)Every year (inspection only): check the fuel and hydraulic hoses for leaks, interference, deformation, ageing, twisting and other damage.
Every 12 monthsAir-Conditioner Pipes and Hoses Check (closed cab)Every year on closed-cab models: check that the lines and clamps are tight and undamaged; repairs go through a Kubota dealer.
Every 2 yearsCoolant ChangeEvery 2 years: drain the coolant, rinse the radiator with water (the chart's separate 2-year radiator system rinse), then refill the radiator and recovery tank with clean water and anti-freeze. Cooling system capacity 11 L. The factory fill is a 50% anti-freeze mix; the manual says the anti-freeze ratio must be less than 50% and that different anti-freeze types must not be mixed.
Every 2 yearsEGR Cooler Hose Replacement (dealer)Every 2 years. A Kubota dealer service.
Every 2 yearsAir-Conditioner Pipes and Hoses Replacement (closed cab)Every 2 years on closed-cab models, or sooner if swollen, hard or cracked. A Kubota dealer service.

Kubota SVL75-2 specifications

  • Type: Compact Track Loader
  • Engine: Kubota V3307-CR-TE4 turbocharged 4-cylinder diesel, 55.4 kW gross / 51.3 kW net, EPA Tier 4 with DPF and EGR
  • Displacement: 3331 cc
  • Oil type: API CJ-4 (DPF-compatible) diesel engine oil: SAE 30, 10W-30 or 15W-40 above 25 C; SAE 20, 10W-30 or 15W-40 at 0-25 C; SAE 10W or 10W-30 below 0 C
  • Oil capacity: 10 L (10.6 US qt) with filter

Kubota SVL75-2 items without a fixed hour interval

  • First Services (new machine): One time on a new machine, before three services settle into their recurring intervals: replace the hydraulic oil filter cartridge after the first 50 hours, and change the drive unit (travel gearbox) oil and replace the hydraulic return filter after the first 250 hours. After that each follows its own 500-hour interval. (Track tension is first checked at 50 hours, which is also its recurring interval.)
  • Manual Edition (Australia) - US Machines: Every interval on this schedule comes from Kubota's SVL75-2 operator's manual, English (Australia) edition (Code No. V0522-5814-4, 2018), the edition Kubota publishes free online. Kubota's US editions (V0521-58122 to V0521-58152, 2014-2023) are sold through kubotaprints.com and were not checked, and they may differ: for the sister SVL97-2, Kubota's US manual changes the engine oil and filter every 500 hours where its Australian manual says 250. Check the manual for your machine's serial number before extending any interval.

Frequently asked questions

How often should I change the oil in a Kubota SVL75-2?

Change the oil in the Kubota SVL75-2 every 250 hours of run time (Australian-edition interval; the US manual may say 500 hours). Replace the oil filter cartridge at the same time. The engine holds 10 L (10.6 US qt) with the filter; use API CJ-4 (DPF-compatible) oil - SAE 10W-30 is listed for every temperature range. Because it is measured in engine hours, log the hour-meter reading rather than a date.

What is the maintenance schedule for a Kubota SVL75-2?

The Kubota SVL75-2 is serviced on engine hours, not miles. Key intervals include Engine Oil and Filter Change (every 250 hours; Australian-edition interval; the US manual may say 500 hours), Air Filter Element Replacement (outer and inner) (every 250 hours), Fuel Filter Cartridge Replacement (every 500 hours). Track the hour meter and service each item when its interval comes due.

Does the Kubota SVL75-2 track maintenance by hours or miles?

By hours. Small engines and heavy equipment log run time on an hour meter, so their service intervals are hours-based. ServiceSage Auto tracks the Kubota SVL75-2 by hours and reminds you when each service is due.