| Interval | Service | Details |
|---|---|---|
| Every 50 hours | Engine Start System Check | Test the seat, PTO clutch lever and speed control pedal safety interlock switches every 50 hours; the engine must not crank or must shut off as designed. |
| Every 50 hours | Greasing | Apply a small amount of multipurpose grease to the grease fittings (top link, lifting rod, speed/brake pedal, battery terminals) every 50 hours; lubricate more often in extremely wet and muddy conditions. |
| Every 50 hours | Wheel Bolt Torque Check | Check wheel bolts and nuts every 50 hours, especially when new, and retighten to the specified torque if loose. |
| Every 100 hours | Battery Condition Check | Check battery condition every 100 hours by reading the indicator (green=good, black=needs charging, white=needs replacing). If used less than 100 hours per year, check fluid level annually instead. |
| Every 100 hours | Air Cleaner Primary Element Clean | Clean the air cleaner primary element every 100 hours; clean more often in severe dusty conditions since a clogged air cleaner can cause regeneration failure. |
| Every 100 hours | Fuel Filter Element Clean (LX2610/LX2610SU) | Clean the fuel filter bowl and element every 100 hours by rinsing in kerosene, then bleed the fuel system after reassembly. |
| Every 100 hours | Fan Belt Tension Adjust | Check and adjust fan belt tension every 100 hours; proper deflection is 7 to 9 mm (0.28 to 0.35 in) at the middle of the span. Replace the belt if damaged. |
| Every 100 hours | Brake Pedal Adjust | Check and adjust brake pedal free travel every 100 hours; proper free travel is 30 to 40 mm (1.18 to 1.57 in), equal on both pedals. |
| Every 200 hours | Engine Oil Change | Change engine oil every 200 hours (4.0 L / 4.2 US qts with filter). The first change must be done after the first 50 hours of operation as a break-in service. |
| Every 200 hours | Engine Oil Filter Replace | Replace the engine oil filter every 200 hours, at the same interval as the oil change. First replacement must be done after the first 50 hours of operation. Use only a Kubota genuine filter. |
| Every 200 hours | Transmission Oil Filters Replace | Replace the transmission oil filter(s) every 200 hours. First replacement must be done after the first 50 hours of operation. Use only a Kubota genuine filter. |
| Every 200 hours | Air Conditioner Drive Belt Tension Adjust (CAB model) | Adjust the air conditioner belt tension every 200 hours (CAB model); proper deflection is 10 to 12 mm (0.4 to 0.48 in) under a 98 N (10 kgf) load. |
| Every 200 hours | Inner Air Filter Clean (CAB model) | Clean the CAB inner air filter every 200 hours by blowing air opposite the normal air flow direction, or soaking in mild detergent water if very dirty. |
| Every 200 hours | Fresh Air Filter Clean (CAB model) | Clean the CAB fresh air filter every 200 hours; do not use gasoline or thinner to clean it. |
| Every 200 hours | Air Conditioner Condenser Check (CAB model) | Check the air conditioner condenser is clean of debris every 200 hours (CAB model). |
| Every 200 hours | Power Steering Oil Line Check | Check power steering lines and hose clamps for tightness and damage every 200 hours; replace or repair at once if worn or damaged. |
| Every 200 hours | Toe-In Adjust | Adjust toe-in every 200 hours; front wheel-to-wheel distance should be 0 to 20 mm (0 to 0.79 in) less than the rear distance. |
| Every 400 hours | Hydraulic Oil Filter Replace | Replace the hydraulic oil filter every 400 hours. Use only a Kubota genuine filter to prevent serious damage to the hydraulic system. |
| Every 400 hours | Transmission Fluid Change | Change the transmission case fluid every 400 hours (15 L / 4.0 US gal of KUBOTA SUPER UDT fluid). Run the engine at medium speed a few minutes after refilling before operating the tractor. |
| Every 400 hours | Front Axle Case Oil Change | Change the front axle gear case oil every 400 hours (4.7 L / 5.0 US qts). |
| Every 400 hours | Front Axle Pivot Adjust | Adjust the front axle pivot every 400 hours; incorrect adjustment can cause front wheel and steering wheel vibration. Consult your local Kubota Dealer for this service. |
| Every 400 hours | Fuel Filter Element Replace (LX2610/LX2610SU) | Replace the fuel filter element every 400 hours, then bleed the fuel system. |
| Every 800 hours | Engine Valve Clearance Adjust | Have the engine valve clearance checked and adjusted every 800 hours. Consult your local Kubota Dealer for this service. |
| Every 1,000 hours | Air Cleaner Primary Element Replace | Replace the air cleaner primary element every 1000 hours or 1 year, whichever comes first. |
| Every 1,000 hours | Air Cleaner Secondary Element Replace | Replace the air cleaner secondary (safety) element every 1000 hours or 1 year, whichever comes first. Do not touch the secondary element except when replacement is required. |
| Every 1,500 hours | Fuel Injection Nozzle Pressure Check | Have the fuel injection nozzle injection pressure checked every 1500 hours. Consult your local Kubota Dealer for this service; this is a registered emission-related critical part. |
| Every 2,000 hours | Cooling System Flush | Flush the cooling system every 2000 hours or 2 years, whichever comes first, using cooling system cleaner per the cleaner's instructions. |
| Every 2,000 hours | Coolant Change | Change the coolant every 2000 hours or 2 years, whichever comes first (4.3 L / 4.5 US qts with recovery tank, ROPS); use a 50/50 mix of ethylene glycol long-life coolant and clean soft water. |
| Every 3,000 hours | Injection Pump Check (LX2610/LX2610SU) | Have the injection pump checked every 3000 hours. Consult your local Kubota Dealer for this service; this is a registered emission-related critical part. |
Change the oil in the Kubota LX2610 every 200 hours of run time. Because it is measured in engine hours, log the hour-meter reading rather than a date.
The Kubota LX2610 is serviced on engine hours, not miles. Key intervals include Engine Start System Check (every 50 hours), Greasing (every 50 hours), Wheel Bolt Torque Check (every 50 hours). Track the hour meter and service each item when its interval comes due.
By hours. Small engines and heavy equipment log run time on an hour meter, so their service intervals are hours-based. ServiceSage Auto tracks the Kubota LX2610 by hours and reminds you when each service is due.