Honda HRN216VKA Maintenance Schedule

Honda HRN216VKA maintenance — the short answer

  • Oil: SAE 10W-30, API SJ or later · 13.5 oz (0.40 L)
  • Oil change interval: every 50 hours or 6 months
  • Engine: Honda GCV170 4-stroke, overhead-valve, single-cylinder, air-cooled
  • Tracked by: hours of use, not miles - Honda lists no hour meter for this model, so keep a run-time log

Honda HRN216VKA maintenance schedule by engine hours

IntervalServiceDetails
Every 50 hours or 6 months, whichever comes firstEngine Oil ChangeOil only - this engine has no oil filter. Change the oil after the first month or 5 hours of use, then every 6 months or 50 hours of use (the schedule also marks the oil change in the 100-hour/every-year and 150-hour/every-two-years columns). Severe duty: change the oil every 25 hours when the mower is used under heavy load or in high outside air temperatures. Oil: SAE 10W-30, API SJ or later; non-detergent oil can shorten engine life and 2-stroke oil can damage the engine. Capacity 13.5 oz (0.40 L); refill amount 12.0 to 13.5 oz (0.35 to 0.40 L), then confirm with the dipstick and do not overfill. Drain the oil while the engine is warm: fuel valve OFF, wipe around the oil filler cap/dipstick and remove it, set a container beside the mower and tilt the mower onto its right side - the oil drains through the filler neck. Allow a couple of minutes for the new oil to settle before measuring.
Every 50 hours or 6 months, whichever comes firstAir Filter CleaningClean the air filter after the first 25 hours of use, then every 6 months or 50 hours of use (also marked at 100 hours/every year); clean it more often when used in dusty areas. Inspect the filter and replace it if damaged. Clean it by tapping it several times on a hard surface, or by blowing compressed air (not exceeding 30 psi / 207 kPa) through it from the inside. Never try to brush off dirt - brushing forces dirt into the fibers. Wipe the inside of the housing and cover with a moist rag without letting dirt into the air duct to the carburetor, then reinstall the filter and cover with both tabs fully locked. Never run the engine without the filter, with a damaged filter or with the cover not properly installed.
Every 50 hours or 6 months, whichever comes firstSmart Drive Cable AdjustmentAdjust the Smart Drive cable at the first 25 hours of use, then every 50 hours or 6 months (also marked at 100 hours/every year and 150 hours/every two years). Dealer item: Honda says an authorized Honda servicing dealer should do this unless you have the proper tools and are mechanically proficient; the procedure is in the Honda shop manual.
Every 100 hours or 12 months, whichever comes firstSpark Plug CheckCheck the spark plug at 100 hours of use or every year. Let the engine cool, disconnect the spark plug cap and clean any dirt from around the plug, then remove it with a 13/16 in (21 mm) spark plug wrench. Replace the plug if the electrodes are worn or the insulator is cracked or chipped. Gap: 0.028 to 0.031 in (0.7 to 0.8 mm); correct it, if necessary, by carefully bending the side electrode.
Every 100 hours or 12 months, whichever comes firstSpark Arrester CleaningOptional part: clean the spark arrester every 100 hours or every year to keep it working as designed. The engine is not factory-equipped with a spark arrester, and in some areas it is illegal to operate an engine without one - check local laws. Let the engine cool, unclip the two red top-cover tabs, remove the three muffler shield bolts with a 10 mm socket wrench, remove the muffler shield and set screw, then take the spark arrester out of the muffler. Brush carbon deposits off the arrester and the exhaust port without damaging the arrester screen, then reinstall it and tighten the three bolts securely. Muffler with spark arrester: Honda part 18300-Z9L-800.
Every 100 hours or 12 months, whichever comes firstGrass Bag CheckCheck the grass bag before each use and at 100 hours of use or every year. Honda grass bag 81320-VR8-N00 (fabric bag only, no frame).
Every 100 hours or 12 months, whichever comes firstBlade Control Operation CheckCheck before each use and at 100 hours of use or every year. Start the engine outdoors and release the blade control lever; the engine should stop quickly. If it does not, take the mower to an authorized Honda servicing dealer for repair.
Every 100 hours or 12 months, whichever comes firstFuel Tank and Filter CleaningClean the fuel tank and fuel filter at 100 hours of use or every year. Dealer item: Honda says an authorized Honda servicing dealer should do this unless you have the proper tools and are mechanically proficient; the procedure is in the Honda shop manual.
Every 100 hours or 12 months, whichever comes firstFlywheel Brake Pad CheckCheck the flywheel brake pad at 100 hours of use or every year. Dealer item: Honda says an authorized Honda servicing dealer should do this unless you have the proper tools and are mechanically proficient; the procedure is in the Honda shop manual.
Every 100 hours or 12 months, whichever comes firstValve Clearance Check and AdjustmentCheck and adjust the valve clearance at 100 hours of use or every year. Cold clearance: intake 0.10 +/- 0.02 mm, exhaust 0.10 +/- 0.02 mm. Dealer item: Honda says an authorized Honda servicing dealer should do this unless you have the proper tools and are mechanically proficient; the procedure is in the Honda shop manual.
Every 100 hours or 12 months, whichever comes firstPinion Gear GreasingGrease the pinion gears at 100 hours of use or every year. Dealer item: Honda says an authorized Honda servicing dealer should do this unless you have the proper tools and are mechanically proficient; the procedure is in the Honda shop manual.
Every 150 hours or 2 years, whichever comes firstAir Filter ReplacementReplace the air filter every 2 years or 150 hours of use. Honda part 17211-Z8B-901 (paper element). Honda recommends a Honda Genuine air filter; a non-Honda filter can let dirt bypass the filter and damage the engine or fuel system.
Every 150 hours or 2 years, whichever comes firstSpark Plug ReplacementReplace the spark plug every 2 years or after 150 hours of use. Plug: NGK BPR5ES (Honda part 98079-55846); an incorrect plug can cause engine damage. Gap 0.028 to 0.031 in (0.7 to 0.8 mm). Install it by hand to avoid cross-threading, then tighten with a 13/16 in (21 mm) spark plug wrench to compress the washer: a new plug 1/2 turn after it seats, a reused plug 1/8 to 1/4 turn after it seats. Spark plug torque: 14 ft-lb (20 N-m). A loose plug can overheat and damage the engine; overtightening can damage the cylinder head threads.
Every 150 hours or 2 years, whichever comes firstTransmission Axle Bearing InspectionInspect, and replace if needed, the transmission axle bearings at 150 hours of use or every two years. Dealer item: Honda says an authorized Honda servicing dealer should do this unless you have the proper tools and are mechanically proficient; the procedure is in the Honda shop manual.
Every 2 yearsFuel Line CheckCheck the fuel lines every 2 years and replace them if necessary. Dealer item: Honda says an authorized Honda servicing dealer should do this unless you have the proper tools and are mechanically proficient; the procedure is in the Honda shop manual.

Honda HRN216VKA specifications

  • Type: Lawnmower
  • Engine: Honda GCV170 4-stroke, overhead-valve, single-cylinder, air-cooled
  • Displacement: 166 cc
  • Oil type: SAE 10W-30, API SJ or later
  • Oil capacity: 13.5 oz (0.40 L)
  • Spark plug: NGK BPR5ES (Honda 98079-55846); gap 0.028 ~ 0.031 in (0.7 ~ 0.8 mm)

Honda HRN216VKA items without a fixed hour interval

  • Engine Oil Level Check: Before each use: check the engine oil level with the dipstick. Always use the dipstick to confirm the actual level, because the amount needed varies with the oil left in the engine after a drain.
  • Air Filter Check: Before each use: check the air filter.
  • Rear Shield Check: Before each use: check the rear shield.
  • Blade Inspection: Before each use: inspect the blades for damage, cracks, and excessive rust or corrosion. Fuel valve OFF, disconnect the spark plug cap and tilt the mower onto its right side (fuel cap side up) first. A dull blade can be sharpened, but a blade that is excessively worn, bent, cracked or otherwise damaged must be replaced. If a blade is bent, take the mower to an authorized Honda servicing dealer for inspection.
  • Blade Mounting Bolt Inspection: Before each use: inspect the blade bolts and washers for damage or looseness. Damaged bolts must be replaced. If a bolt is loose, tighten it with a torque wrench to the blade bolt torque of 36 to 43 ft-lb (49 to 59 N-m); with no torque wrench, take the mower to an authorized Honda dealer. Use only Honda Genuine blade bolts and special washers: blade bolt 90105-VA3-J01 (2 required, 10 x 25 mm) and spring washer 90502-VG3-000 (2 required). Bolts torqued wrongly can let the blades loosen and be thrown from the mower.
  • Blade Replacement: As needed - replace blades that are excessively worn, bent, cracked or damaged. Fuel valve OFF, disconnect the spark plug cap, tilt the mower onto its right side (fuel cap side up). Wear thick leather gloves and hold the blades by hand, then remove the blade bolts with a 14 mm (6 point) socket wrench. Inspect the blade holder and mounting surface; if it is damaged or the blades hit a hard object, the blade holder should also be replaced. Always install the upper and lower blades as a set, with Honda Genuine blade bolts and special washers, and tighten the bolts with a torque wrench to 36 to 43 ft-lb (49 to 59 N-m). Parts: lower blade 72511-VR8-M00, upper blade 72531-VR8-M00, blade bolt 90105-VA3-J01 (2), spring washer 90502-VG3-000 (2).
  • Storage Preparation: Winterization for storage (the warranty does not cover fuel system damage or engine performance problems from neglected storage preparation). (1) FUEL - drain or treat it. More than 3 months before next use: start the engine and run it until all the gasoline is out of the entire fuel system, including the tank; do not leave gasoline in the mower for more than 3 months of inactivity. 1 to 3 months before next use: if you did not add fuel stabilizer when you filled your storage tank, fill the mower tank with fresh gasoline and add fuel stabilizer according to the stabilizer maker, run the engine outdoors for 10 minutes, then stop it, turn the fuel valve OFF, restart it and let it run until it runs out of gasoline (about 3 minutes). 3 to 4 weeks before next use: turn the fuel valve OFF and fill the tank, then with the valve off start the engine and let it run until it runs out of gas (about 3 minutes). Honda recommends Pro Honda Fuel Stabilizer (08732-0800, 8 oz). (2) OIL - change the engine oil (see Engine Oil Change), then remove the spark plug, pour a teaspoon (5 cc) of clean engine oil into the cylinder, pull the starter rope several times to distribute it, reinstall the plug, and pull the starter rope slowly until resistance is felt before returning the grip gently - this closes the valves so moisture cannot enter the cylinder. (3) CLEAN - let the engine cool; before washing the underside of the deck, stop the engine, turn the fuel valve OFF and rest the mower on its right side (fuel cap side up), wear heavy gloves and remove clippings (especially around the Clip Director shutter lever and housing); keep water out of the controls, cables, air cleaner and muffler opening; wash the engine by hand, never with a hose or pressure washer that can force water into the air filter; wash the grass bag with a hose or pressure washer and let it dry completely. (4) DRY - wipe all accessible surfaces dry, run the engine outdoors on a level surface until it reaches normal operating temperature to evaporate remaining water, let it cool, touch up damaged paint and coat areas that may rust with a light film of oil. (5) STORE - fuel valve OFF, on a level surface (tilting can cause fuel or oil leakage), in a well-ventilated dry area away from any appliance with a flame (furnace, water heater, clothes dryer) and away from spark-producing electric motors or power tools; cover the cool mower to keep out dust, never with sheet plastic, which traps moisture and promotes rust (Honda lawn mower cover 08P59-VE2-000AH is breathable); remove the grass bag and fold the handlebar by turning the adjust knobs 90 degrees and folding it forward without pinching or kinking the cables.
  • Spring Start-Up After Winter: Removing the mower from storage: when unfolding the handlebar, lock the handlebar adjust knobs to secure it in the mowing position. Check the mower as described in BEFORE OPERATION (page 4 of the manual). If the cylinder was coated with oil during storage preparation, the engine may smoke briefly at startup.

Frequently asked questions

How often should I change the oil in a Honda HRN216VKA?

Change the oil in the Honda HRN216VKA every 50 hours of run time or every 6 months, whichever comes first. On a new mower, do the first change after 5 hours or the first month. There is no oil filter: refill with 12.0 to 13.5 oz (0.35 to 0.40 L) of SAE 10W-30 oil, API SJ or later, and confirm the level with the dipstick. Change it every 25 hours instead if the mower works under heavy load or in high outside air temperatures. Honda does not list an hour meter for this model, so keep a rough log of the hours you run it.

What is the maintenance schedule for a Honda HRN216VKA?

The Honda HRN216VKA is serviced on engine hours, not miles. Key intervals include Engine Oil Change (every 50 hours or 6 months), Air Filter Replacement (every 150 hours or 2 years), Spark Plug Replacement (every 150 hours or 2 years). Without an hour meter, log your run time and service each item when its interval (or its yearly limit) comes due.

Does the Honda HRN216VKA track maintenance by hours or miles?

By hours of run time, with a yearly limit on several items. Honda does not list an hour meter for this model, so estimate its hours from a simple run-time log. ServiceSage Auto tracks it by hours and reminds you when each service is due.